BaBylissPRO ceramic dryer is both compact and powerful. And whoever quoted you the $1000 to set up the correct switch is a crook. Dont take the chance of death of the poor fool out on the pole or the live male plug falling out of the dryer end and FRYING someone. You may know what you are doing but let’s say you kick the bucket and your stupid brother-in-law ends up with your generator and jerry rigged cable. He does not know better and uses the set up and kills someone. Gas leak detectors are sold at home centers, hardware stores and online.
Take the time to remove any other installed plugs. They should come together to finish this connection. Attach each of the water supply hoses to the faucets.
How to hook up a new gas stove and range
The hoses that run between the clothes dryer and the vent are generally 4 inches in diameter, but those on larger dryers can be as wide as 6 inches. Are you left with a few remaining questions about selecting the best dryer vent hose for tight space requirements? Read candy dating how to see who likes you on without paying the FAQs below to learn other key details related to dryer vent hoses. Look for the shortest path possible with the fewest number of turns. Longer paths and multiple turns in the hose can increase the risk of lint getting trapped, creating a potential fire hazard.
The center wire of this cable is the neutral wire and the outer wires are the «hot» line 1 and line 2 wires. In the dryer’s wire connection box, there must be a metal jumper between the center neutral terminal and the ground terminal. To replace a dryer vent hose, start by unplugging the dryer from the wall . Loosen the existing dryer vent from the dryer and where it connects to the outside using a screwdriver and remove the hose.
Keep in mind that your dryer will need about four inches of additional space in the back for venting. While an acceptable practice some years ago, as stated in the opening, this practice has been banned in the U.S. by the NEC. The only safe, legal way to connect 4 wire ranges and dryers is with a 4 wire cord set to a 4 wire receptacle fed by a four wire circuit.
If you’ve used the washer previously, there may be water in the hose that you’ll need to drain or dry with your towel before proceeding. If cutting through stucco or brick, use a hammer drill and a 1/4-inch masonry bit to create both the pilot hole and to cut out the vent hole. Transfer that measurement inside, if necessary, to mark the new dryer vent center.
iPower GLDUCT4X8C Non-Insulated Flex Dryer Vent Hose
The downside is that it will be harder to hide the screws. The shelf is pretty heavy and this cleat is holding it up. Pull warm towels straight from the dryer in this combo room. A louvered door discreetly separates the laundry from the bathing area and provides extra ventilation for the machines.
The white wire from both cords is connected, which gives you a double wire for the standard connection. The breaker box will let you know the amount of voltage running through the circuit. Choose two outlets that are on separate breakers that are touching each other inside of the breaker box. Next, disconnect the water inlet from your washer.
This helps to ensure a smooth installation process and prevent damage to the appliance and surrounding area. Shop washing machine hoses from Maytag for your installation process. Check inside the washer for the installation instructions and the drain hose. The steps in this guide are generalized, so model-specific instructions will be your best resource. The installation process is very similar to top load washers, though front load washers are stackable. If you want to save space by stacking, read the Maytag® guide to stacking front load washers and dryers.
Given that a dryer is a metal-chassis piece of equipment, that metal chassis works against you without proper grounding, and works in your favor with. If the neutral is bare, that’s allowed because the cable is grandfathered, but wrap it with tape so they don’t short out. Neutral is not ground, and will be a fraction of a volt higher than ground when the machine is at full load, and you don’t want it taking ground as an alternate path. The instructions are telling you to do something which is not proper.
If your vent path seems indirect or unnecessarily complicated, consider contacting a professional to help improve the path for you. Homer Flores is an Appliance Repair Specialist and Training Manager at PreFix, a home maintenance company out of Austin, Texas. With over 15 years of experience, Homer specializes in home improvement, remodeling, and construction.
Does a dryer have to be vented outside?
In a large room, you can space the washer and dryer evenly from the wall to compensate for the dryer’s ventilation needs. In a small laundry closet, especially one with doors, you may not have that luxury. Altering the setup or modifying the exhaust vents can make a big difference. Connect the red and black hot circuit wires to the two screw terminals on the 30-amp, double-pole circuit breaker.